Fallout 4 Laser rifle
by ArakanI 19 February 2016 in Games & Cosplay
Report abuse
by ArakanI 19 February 2016 in Games & Cosplay
A laser rifle modeled after the asset from Fallout 4. All parts are scratch made with an exported model as reference.
I left out some details. Some because they were to small, some because I didn’t like them.
The uploaded model have some details that i missed on my test prints, and because I had already assembled the model I won’t reprint those parts.
Final assembled model is about 78 cm long if you print it at the exported scale.
I have no idea about how big the gun should be to be at 1:1 scale. I made the model so one unit of the imported model is one centimeter when i exported the .stl.
Instructions
Some parts need support material.
If possible, don’t use a raft.
Print at 0.2 mm or less.
I used a light infill, around 20%.
You have to glue the model together, it’s not snap fit.
The pins are there to make it easier to put together.
You can replace the printed cables with real cables, just drill out the parts the cable go through at a diameter that matches your cables.
You can use this image to get a better understanding of how it goes together: http://nukeaduke.com/img/laserRifleExploded.jpg
Don’t try and print the “Assembled” part, it won’t print well!
| Last Update | Type | Downloads | Size | |||
|---|---|---|---|---|---|---|
|
|
laserRifleBackKnob.stl | 19 February 2016 |
.stl | 159 | 95,88 KB | |
|
|
laserRifleBarrel_1.stl | 19 February 2016 |
.stl | 159 | 13,66 KB | |
|
|
laserRifleBarrel_2.stl | 19 February 2016 |
.stl | 159 | 557,11 KB | |
|
|
laserRifleBarrel_3.stl | 19 February 2016 |
.stl | 159 | 521,37 KB | |
|
|
laserRifleBarrel_4.stl | 19 February 2016 |
.stl | 159 | 57,31 KB | |
|
|
laserRifleBarrel_5.stl | 19 February 2016 |
.stl | 159 | 344,81 KB | |
|
|
laserRifleBarrel_6.stl | 19 February 2016 |
.stl | 159 | 203,99 KB | |
|
|
laserRifleBarrel_7.stl | 19 February 2016 |
.stl | 159 | 69,22 KB | |
|
|
laserRifleCables_1.stl | 19 February 2016 |
.stl | 159 | 555,65 KB | |
|
|
laserRifleCables_2.stl | 19 February 2016 |
.stl | 159 | 221,37 KB | |
|
|
laserRifleFrontGrip_1.stl | 19 February 2016 |
.stl | 159 | 332,41 KB | |
|
|
laserRifleFrontGrip_2.stl | 19 February 2016 |
.stl | 159 | 435,24 KB | |
|
|
laserRifleGrip.stl | 19 February 2016 |
.stl | 159 | 938,75 KB | |
|
|
laserRifleLevers.stl | 19 February 2016 |
.stl | 159 | 110,63 KB | |
|
|
laserRifleMFCell.stl | 19 February 2016 |
.stl | 159 | 256,33 KB | |
|
|
laserRifleMuzzle.stl | 19 February 2016 |
.stl | 159 | 505,55 KB | |
|
|
laserRiflePlugs.stl | 19 February 2016 |
.stl | 159 | 327,62 KB | |
|
|
laserRifleReceiver_1.stl | 19 February 2016 |
.stl | 159 | 1,38 MB | |
|
|
laserRifleReceiver_2.stl | 19 February 2016 |
.stl | 159 | 358,77 KB | |
|
|
laserRifleReceiver_3.stl | 19 February 2016 |
.stl | 159 | 220,79 KB | |
|
|
laserRifleReconSight_1.stl | 19 February 2016 |
.stl | 159 | 132,6 KB | |
|
|
laserRifleReconSight_2.stl | 19 February 2016 |
.stl | 159 | 90,12 KB | |
|
|
laserRifleReconSight_3.stl | 19 February 2016 |
.stl | 159 | 301,55 KB | |
|
|
laserRifleStock_1.stl | 19 February 2016 |
.stl | 159 | 732,21 KB | |
|
|
laserRifleStock_2.stl | 19 February 2016 |
.stl | 159 | 564,24 KB | |
4 Comments
You must be logged in to post a comment.
You must be logged in to post a comment.
I’ve almost completed printing this but the gap in “laserRifleBarrel_1.stl” is a bit small. When you try put trigger part into riflebarrel_1 it doesnt go in. So i did cut one side of it , glue all of them together.
Hmm, that is weird. For me it was a perfect fit. I didn’t even have to clamp it together when i glued it together.
Did you print it in ABS or any other kind of material?
I’ve completed the print and put it together. Yes , i’ve used ABS. Maybe that was the problem. Don’t know but it did work.
This size is better than original one! Goof job!
Fallout 4 Laser rifle
by ArakanIAdd this project to collection