Clamp for vertical use. Photo and video shooting
by Perinski 20 December 2018 in Household Objects
Report abuse
by Perinski 20 December 2018 in Household Objects
https://www.thingiverse.com/thing:3084138
The clamp is suitable for use by small cameras like Hero or Yi 4k + and other similar ones. You can also use smartphones for shooting.
The clamp can be mounted on the shelf or edge of the table. Using the ball head – the viewing angle is not limited. Also suitable for other devices for installing cameras.
I used tubes with a diameter of 8 mm, a wall thickness of 1 mm. Anodized aluminum. Threaded stud – M5 length 110 mm. Rubber substrate can be printed with soft filaments.
Some parts have to be glued together, but I’m sure you can do it 
In principle, it was possible to make clamps and thinner, but I was reinsured and made a margin of safety. In the video, I showed the stages of assembly of some parts.
For the options of suitable ball heads, see below.
Mini Ball Head – http://ali.pub/2z2lot
Ball Head v1 – http://ali.pub/2z2lt3
Ball Head v2 – http://ali.pub/2z2m0h
Ball Head v3 – http://ali.pub/2z2m37
Ball Head v4 – http://ali.pub/2z2m6b
Buy & save with cashback —> http://ali.pub/2v0znm
Donate with PayPal —> https://www.paypal.me/perinski
Instagram —> https://www.instagram.com/v.perinski/
Twitter —> https://twitter.com/v_perinski
Pinterest —> https://www.pinterest.com/v_perinski/
Tingiverse —> https://www.thingiverse.com/thing:2110500
Facebook —> https://www.facebook.com/3DPrinting.stl/
| Last Update | Type | Downloads | Size | |||
|---|---|---|---|---|---|---|
|
|
Cap.STL | 20 December 2018 |
.STL | 2 | 769,22 KB | |
|
|
Clamp-Fix-Slide.STL | 20 December 2018 |
.STL | 2 | 3,89 MB | |
|
|
Clamp-Fix.STL | 20 December 2018 |
.STL | 2 | 4,3 MB | |
|
|
Clamp-slide-1.STL | 20 December 2018 |
.STL | 2 | 377,23 KB | |
|
|
Clamp-slide.STL | 20 December 2018 |
.STL | 2 | 120,79 KB | |
|
|
Knob-Bolt-M4-A.STL | 20 December 2018 |
.STL | 2 | 2,91 MB | |
|
|
Knob-Bolt-M4-B.STL | 20 December 2018 |
.STL | 2 | 2,87 MB | |
|
|
Knob-Bolt-M5-A.STL | 20 December 2018 |
.STL | 2 | 4,53 MB | |
|
|
Knob-Bolt-M5-B.STL | 20 December 2018 |
.STL | 2 | 4,54 MB | |
|
|
Knob-for-Tread.STL | 20 December 2018 |
.STL | 2 | 133,68 KB | |
|
|
Ruber.STL | 20 December 2018 |
.STL | 2 | 914,05 KB | |
Be the First to Comment!
You must be logged in to post a comment.
You must be logged in to post a comment.
Clamp for firmware controllers 8 pins
by PerinskiClamp for firmware controllers 4 pins
by PerinskiStencil Printer
by PerinskiMicroscope Stand
by PerinskiContainer for lens and filters
by PerinskiSanding Tool
by PerinskiAdd this project to collection