Stencil Printer

by Perinski 16 February 2019 in Engineering

Report abuse

  • 0

  • 2109

  • 0

  • 26

License: Creative Commons - Attribution - Non-Commercial

All details of the manufacture and use – see the video. Unfortunately the video did not work short :)

Materials used:
Aluminum Extrusion Profile 20×20 mm – http://ali.pub/34cu8s
Aluminum corner 20×20 mm – http://ali.pub/34cujo
Profile end cap 2020 mm – http://ali.pub/34cupb
T-Fastener Sliding Nut M3/M5 – http://ali.pub/34cute
Aluminium Tube Pipe 10x10x1 mm – http://ali.pub/34cuy2
Aluminium solid round bar rod 5mm – http://ali.pub/34cv1r
Lubricating Bearing Bushing 4x6x10 mm – http://ali.pub/34cv68
Cylindrical position pins 4×30 mm – http://ali.pub/34cvba
Galvanized iron sheet 0.8 mm – ???
Springs – http://ali.pub/34cvee
Screws/washers М3/M5 – http://ali.pub/34cvlz
Set screws – http://ali.pub/34dg8r
Insert Nuts M3 – http://ali.pub/34cvop
Thread Bar M3 – http://ali.pub/34cvu5
Thread Bar Brass M3 – http://ali.pub/34cykq
Strong Round Magnets 10X3 mm http://ali.pub/34cw2p
Rubber feet 13x10x7 mm – http://ali.pub/34cw8q
Glue B-7000 – http://ali.pub/34cwlr
Double-sided Transparent Clear Adhesive Tape 50M 5MM – http://ali.pub/34cwsy
Tools that helped to complete the project:
NOGA deburring tool and Blades – http://ali.pub/2z2ah5
Digital Microscope – http://ali.pub/329tle
Reamers Small – http://ali.pub/34cwvv
Reamers – http://ali.pub/34cx0c
Threading Tools – http://ali.pub/34cx3n
Automatic Center Pin Punch – http://ali.pub/34cx6d
Digital Vernier Caliper – http://ali.pub/34cx9v
Drill Bit HSS – http://ali.pub/34cxd6
Circular Saw Blades – http://ali.pub/34cxi8
Drill Press Stand – http://ali.pub/34cxky
Coordinate Table – http://ali.pub/34cxno
Coordinate Table with bearings – http://ali.pub/34cxqs
HILDA 400W – http://ali.pub/34cxuh
Scraper – http://ali.pub/34cxxe
High precision vise – http://ali.pub/34cy1o
Reflow Solder Oven – http://ali.pub/34cy4l
Press Pump Bottle – http://ali.pub/34cybe
Solder Paste – http://ali.pub/34cy83
You can make a printer for any stencil format. I use 190×200 mm. A little later I’ll post the source

Buy & save with cashback – http://ali.pub/2v0znm

Donate with PayPal – https://www.paypal.me/perinski
Instagram – https://www.instagram.com/v.perinski/
Twitter – https://www.twitter.com/v_perinski
Pinterest – https://www.pinterest.com/v_perinski/
Thingiverse – https://www.thingiverse.com/thing:2110500
Facebook – https://www.facebook.com/3DPrinting.stl/

Be the First to Comment!


wpDiscuz
Clamp for firmware controllers 8 pins
 
0

Clamp for firmware controllers 8 pins

by Perinski
 
 
Views 2143
 
 
Comments 0
 
 
Downloads 44
 
Clamp for firmware controllers 4 pins
 
2

Clamp for firmware controllers 4 pins

by Perinski
 
 
Views 4532
 
 
Comments 0
 
 
Downloads 51
 
Stencil Printer
 
0

Stencil Printer

by Perinski
 
 
Views 2109
 
 
Comments 0
 
 
Downloads 26
 
Microscope Stand
 
1

Microscope Stand

by Perinski
 
 
Views 3911
 
 
Comments 0
 
 
Downloads 75
 
Container for lens and filters
 
0

Container for lens and filters

by Perinski
 
 
Views 1770
 
 
Comments 0
 
 
Downloads 102
 
Sanding Tool
 
2

Sanding Tool

by Perinski
 
 
Views 6179
 
 
Comments 0
 
 
Downloads 69